Log of SV Free Spirit and ships company

The chronicles of the schooner Free Spirit and her crew, embarking on an open ended journey upon the great rolling heap. Free Spirit is currently pursuing humanitarian and commercial goals in the Dominican Republic, on the island of Hispaniola. Working under the Ocean Reach USA and Paradigm Research banners, she is serving as logistics headquarters, workshop, and development laboratory for many ongoing projects. This is the log of her journey.....

Google
 
Web sailfreespirit.blogspot.com
If you are joining us for the first time, click here for an introduction!
Books and more, at the Schooner Free Spirit Chandelry
Clothes and more, at the Free Spirit Logo Shop!

Tuesday, July 21, 2009

Drake And Maya Up The Mast

Drake had been begging to go up the mast for a really long time, so today was the day. Blayde hauled him up in the Bosun's Chair, and then Drake had to climb out of the chair onto the spreader bars and then into the crow's nest. I had to pretend it wasn't really happening :-) He was SOOOO proud of himself!!



Heading up....



Coming down....



I am sad that I could not get better pictures of Maya up the mast because it was dark. As I have said before on the blog, Maya and Finn from SY Tranquility are little monkeys. It was after our Easter Potluck party that she decided to give the crow's nest a try. If you look closely, you can see her little 7 year old legs dangling to the left of the right light. We ended up drawing the line at the spreader bars, and did not allow her to climb into the crow's nest.



Leigha, on the left, watches with apprehension.....



Oh ya, did I forget to mention that she went up and back down the mast by herself, and by hand up the lines next to the mast? It was amazing to watch!!



0 Comments:

Post a Comment

<< Home

Introducing Propcalc 4.0

Use Propcalc to easily match your hull with your engine, transmission, and propeller
Put the known data in the top fields, then hit the Update button to get the answers.
Results, of course, should be verified by a Naval Architect or qualified surveyor.
Data is provided for three bladed propellers of average type
For two or four bladed props, use the modifiers shown below.

Fill out the fields as follows:

Vessel LWL (ft) = Waterline length
Vessel Disp (lbs) = Vessel displacement
(max) HP = Rated Engine Max HP
Engine RPM max = Engine RPM at Max HP
Engine RPM cruise = Desired or estimated cruise rpm
(Cruise or Max) Kts = Speed to work the calculations for
Slip = Propeller efficience. 45% is average for a displacement cruiser.
Gear ratio = 1: Gear ratio of transmission
SL Ratio Adj. = This value will be added (or subtracted, if a negative value) to the calculated S/L ratio.

Key information:

If the "hp required" is greater than the "cruse HP", you have your cruise RPM set too low for your engine parameters.
If the "hp required" is significantly less than the "cruse HP", you have your cruise RPM set too high for your engine parameters.
If the "hp required" is greater than the "Max HP", then your target speed is too high for your engine/hull parameters.
The S/L ratio is calculated automaticaly based on your input. It can be adjusted if necessary, but normally it should be left alone.
If the calculated S/L ratio exceeds S/L MAX, then the results are likely to be non-predictive. Try a lower speed requirement.
SL Ratios of 1.1 - 1.4 are typical of displacement hulls. Semiplaning or planing hulls can go higher.

Typical propeller slip values:

Sailing auxiliary, barges, etc less than 9 Kts............45%
Heavy powerboats, workboats 9 - 15 Kts....................26%
Powerboats, Lightweight Cruisers 15 - 30 Kts..............24%
High speed planing boats 30 - 45 Kts......................20%
V bottom race boats 45 - 90 Kts...........................10%


Note:

it is possible to get irrational answers by irrational input , I.E specifying excessive speed for hull type and length
Any attempt to exceed hull speed (1.34 times the square root of the waterline length in feet) with a displacement hull are likely
to fail unless the hull is extremely fine (multihull) or otherwise exceptional. In such cases, an S/L adjustment would be in order.

2 and 4 bladed props:


For two bladed propellers, multiply the diameter by 1.05, and the pitch by 1.01
For four bladed propellers, multiply the diameter by .94, and the pitch by .98


PROPCALC
  Inputs:
Vessel LWL (ft) =
Vessel Disp (lbs) =
  (max) HP =
  Engine RPM max =
  Engine RPM cruise =
  (Cruise or Max) Kts =
  Slip =
  Gear ratio = 1:
  SL Ratio Adj. =
   
    Solutions:
  Prop rpm max =
  Prop rpm cruise =
  Pitch =
  Diameter =
  Static Thrust =
  Cruise HP =
  Cruise HP% =
  SL Ratio =
  DL Ratio =
  SL Max =
  HP Required =