Log of SV Free Spirit and ships company

....the chronicles of a family of five, embarking on an open ended journey upon the great rolling heap. In choosing this path, we invite dangers, joys, sorrows, and triumphs, facing not only the vastness of the sea, but -perhaps yet greater- the vastness of the soul. This is the log of our journey.....

Free Spirit Bookstore

Free Spirit Logo Shop!

Warming colors indicate increasing anomalous quantum synchronization of random event generators. Persistent anomalies precede or coincide with events of global significance with improbable regularity, for reasons mankind has yet to understand.

Open a mini window.

Wednesday, December 26, 2007

Yet Another Misc. Post

Shep, always eager and waiting for a trip up the mast, does the first hanging of Christmas lights on Free Spirit.

Stringing them on the tweenstay between the aft and forward masts.

Just hangin' out ;-)

A happy moment!!!

Knowing that sunsets are one of my favorite natural occurrences, Blayde took this picture for me as a surprise.

Shep sharing a little George Carlin, for an afternoon laugh or two or three!!

Raoul gets some valuable lessons on rope splicing from Dad, who is the true splicing expert. It was nice to see them working together again!

~Shep and his Bapa ~

Suzy was down from Fairbanks visiting her family in the Tampa area, and although her visit was short, we really enjoyed seeing her and showing her the boat.

Valin, laughing hysterically as her falls through the bottom of a cloth chair...

0 Comments:

Links to this post:

<$BlogBacklinkTitle$>: <$BlogBacklinkSnippet$>
posted by <$BlogBacklinkAuthor$> @ <$BlogBacklinkDateTime$>

Create a Link

<< Home

Introducing Propcalc 4.0

Use Propcalc to easily match your hull with your engine, transmission, and propeller
Put the known data in the top fields, then hit the Update button to get the answers.
Results, of course, should be verified by a Naval Architect or qualified surveyor.
Data is provided for three bladed propellers of average type
For two or four bladed props, use the modifiers shown below.

Fill out the fields as follows:

Vessel LWL (ft) = Waterline length
Vessel Disp (lbs) = Vessel displacement
(max) HP = Rated Engine Max HP
Engine RPM max = Engine RPM at Max HP
Engine RPM cruise = Desired or estimated cruise rpm
(Cruise or Max) Kts = Speed to work the calculations for
Slip = Propeller efficience. 45% is average for a displacement cruiser.
Gear ratio = 1: Gear ratio of transmission
SL Ratio Adj. = This value will be added (or subtracted, if a negative value) to the calculated S/L ratio.

Key information:

If the "hp required" is greater than the "cruse HP", you have your cruise RPM set too low for your engine parameters.
If the "hp required" is significantly less than the "cruse HP", you have your cruise RPM set too high for your engine parameters.
If the "hp required" is greater than the "Max HP", then your target speed is too high for your engine/hull parameters.
The S/L ratio is calculated automaticaly based on your input. It can be adjusted if necessary, but normally it should be left alone.
If the calculated S/L ratio exceeds S/L MAX, then the results are likely to be non-predictive. Try a lower speed requirement.
SL Ratios of 1.1 - 1.4 are typical of displacement hulls. Semiplaning or planing hulls can go higher.

Typical propeller slip values:

Sailing auxiliary, barges, etc less than 9 Kts............45%
Heavy powerboats, workboats 9 - 15 Kts....................26%
Powerboats, Lightweight Cruisers 15 - 30 Kts..............24%
High speed planing boats 30 - 45 Kts......................20%
V bottom race boats 45 - 90 Kts...........................10%

Note:

it is possible to get irrational answers by irrational input , I.E specifying excessive speed for hull type and length
Any attempt to exceed hull speed (1.34 times the square root of the waterline length in feet) with a displacement hull are likely
to fail unless the hull is extremely fine (multihull) or otherwise exceptional. In such cases, an S/L adjustment would be in order.

2 and 4 bladed props:

For two bladed propellers, multiply the diameter by 1.05, and the pitch by 1.01
For four bladed propellers, multiply the diameter by .94, and the pitch by .98

PROPCALC
		Inputs:
Vessel LWL (ft) =
Vessel Disp (lbs) =
	(max) HP =
	Engine RPM max =
	Engine RPM cruise =
	(Cruise or Max) Kts =
	Slip =
	Gear ratio = 1:
	SL Ratio Adj. =

		Solutions:
	Prop rpm max =
	Prop rpm cruise =
	Pitch =
	Diameter =
	Static Thrust =
	Cruise HP =
	Cruise HP% =
	SL Ratio =
	DL Ratio =
	SL Max =
	HP Required =